BOSCH 06L906036AJ
High Pressure Fuel Injector VW Golf 7 GTI Audi A3 A4 B9 EA888 Gen 3 2.0 TSI
06L906036AE, 0261500246, 0261500245HIGH-SPEED PEAK-AND-HOLD SOLENOID ACTUATED NEEDLE VALVE-200 bar peak rail pressureProduct Overview
The Bosch 06L906036AJ is a Bosch HDEV5 multi-hole gasoline direct injection injector for Volkswagen and Audi EA888 Gen 3 and Gen 3B 1.8L / 2.0L TSI / TFSI engines (CHHB / CJXC / CYFB). It is listed for the Golf VII GTI 2.0 TSI (2013-2020), Audi A4 B9 (2015-2023) and S3 8V (2013-2020). Nominal rail injection pressure is 200 bar (20 MPa / 2900 psi), with a 6-hole laser-drilled asymmetrical combustion bowl pattern and coil resistance of 1.5-2.0 Ω at 20°C. Fuel rail clamping fasteners take 9 N·m and the high-pressure feed line flare nut 27 N·m. Common codes are P0300, P0301-P0304 and P0172. New Teflon combustion seal rings must be calibrated with T10133 tool cones before insertion into the cylinder head.
Always verify the OE reference 06L906036AE stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 06L906036AJ needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf VII GTI 2.0 TSI | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2013-2020 |
| Audi A4 (B9) | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2015-2023 |
| Audi S3 (8V) | Volkswagen / Audi EA888 Gen 3 & Gen 3B (1.8L & 2.0L TSI / TFSI CHHB / CJXC / CYFB) | 2013-2020 |
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDEV5 Multi-Hole Gasoline Direct Injection Injector |
| Operating PressureCore Spec | |
| Spray Pattern | 6-hole laser-drilled asymmetrical direct combustion bowl pattern |
| Hold-down Torque | 9 N·m Fuel Rail Clamping Fasteners📐 Torque & Angle Wizard → |
| High Pressure Feed Line Torque | 27 N·m Flare Nut Connection |
| Coil Resistance | 1.5 - 2.0 Ω at 20°C (Direct peak-and-hold driver circuit) |
| Common Fault Codes | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0172 (System Too Rich Bank 1) |
| Workshop Precaution | Always calibrate new Teflon combustion seal ring using T10133 tool cones before cylinder head insertion |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel Rail & Remove Intake Manifold: Depressurize high-pressure fuel rail via diagnostic scan tool or fuse pull. Remove upper intake manifold to access high pressure fuel rail assembly.
- Extract Fuel Rail & Remove Injectors: Unbolt fuel rail holding bolts (9 N·m). Use slide hammer puller T10133/1 to gently extract fuel injectors from cylinder head combustion chambers.
- Calibrate New Teflon Combustion Chamber Seal: Cut and remove old combustion seal without scratching injector groove. Install new Teflon ring using expansion cone T10133/2 and compress with sizing collar T10133/3.
- Seat Injectors & Torque Rail Bolts: Push injectors into cylinder head bores by hand. Torque rail retaining bolts evenly to 9 N·m. Torque high-pressure pipe union nut to 27 N·m.
- Tighten the injector mounting/hold-down to 9 N·m and the high-pressure line to 27 N·m.
- Verify the application is a 200 bar gasoline direct-injection EA888 Gen 3/Gen 3B system before installation.
- Match the old injector and vehicle EPC to 06L906036AJ or the listed cross references before fitting.
Frequently Asked Questions
Will this injector fit my Golf VII GTI 2.0 TSI, Audi A4 B9, or Audi S3 8V?
This gasoline direct-injection injector is listed for Volkswagen Golf VII GTI 2.0 TSI (2013-2020), Audi A4 B9 (2015-2023), and Audi S3 8V (2013-2020). It is also listed for Volkswagen/Audi EA888 Gen 3 & Gen 3B 1.8L & 2.0L TSI/TFSI CHHB / CJXC / CYFB applications. Confirm exact vehicle fitment against the vehicle's EPC before ordering.
What diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes for this gasoline direct-injection injector are P0300, P0301, P0302, P0304, and P0087. These are the only DTCs provided in the verified facts, so confirm diagnosis against the vehicle's EPC instead of guessing.
Do I need coding or adaptation, and can I reuse the seals?
Coding/adaptation requirements and seal reuse are not stated in the verified facts. Confirm both against the vehicle's EPC before installation rather than guessing.
How can I verify the old part and cross-reference the replacement?
The part number is 06L906036AJ, and the listed cross references are 06L906036AJ, 06L906036AE, 0261500246, 0261500245, 0261500162, and 04E906036Q. Compare the old injector markings and the vehicle's EPC against these numbers before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.