Catalog / HYUNDAI / 35320-2G700
HYUNDAI

HYUNDAI 35320-2G700

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

High Pressure Fuel Pump Sonata Optima Santa Fe Sorento Sportage 2.0T 2.4L Theta II GDI 353202G700

Reference data for HYUNDAI 35320-2G700 high-pressure fuel pump · OEM 35320-2G720, 35320-2G730, GDP206, HM10014, 353202G740 · Application Hyundai / Kia 2.0L T-GDI & 2.4L GDI Theta II (G4KH / G4KJ)
OE REFERENCE35320-2G720, 35320-2G730, GDP206, HM10014, 353202G740
CONTROL VALVEINTEGRATED HIGH-SPEED PULSE-WIDTH MODULATED METERING VALVE
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Hyundai 35320-2G700 (superseded by factory service part numbers 35320-2G720, 35320-2G730, and 35320-2G740) is the original equipment high-pressure mechanical fuel pump designed for Hyundai and Kia's Theta II 2.0-liter Turbo and 2.4-liter naturally aspirated Gasoline Direct Injection (GDI) engines. Operating at up to 150 bar (2175 psi), this pump mounts directly atop the cylinder head valve cover, driven by a dedicated lobe on the exhaust camshaft across millions of popular passenger vehicles including the Sonata, Optima, Santa Fe, Sorento, and Sportage. Theta II GDI engines are notorious for drivability failure modes associated with the high-pressure fuel pump. Common symptoms include engine hesitation under load, limp-mode RPM limits (restricted to 2500-3000 RPM), extended cold cranking, and DTC P0087 (Fuel Rail Pressure Too Low), often accompanied by P0088 (Rail Pressure Too High) and misfire codes P0300. Internal seal rupture also allows pressurized fuel to drain into the valve cover and engine crankcase, diluting engine oil and contributing to Theta II connecting rod bearing seizure. Replacing the HPFP restores stable fuel rail pressure and smooth acceleration. Workshop protocol mandates drawing down mounting bolts alternately to 13 N·m (115 in-lb) and securing the high-pressure steel delivery tube to 28 N·m (21 lb-ft). Technicians must inspect the roller lifter tappet for scuffing and change engine oil immediately if fuel dilution is detected on the dipstick.

Before You Order

Always verify the OE reference 353202G720, 353202G730, GDP206, HM10014 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 35320-2G700 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Hyundai SonataG4KH / G4KJ2011-2019
Kia OptimaG4KH / G4KJ2011-2020
Hyundai Santa Fe SportG4KH / G4KJ2013-2018
04

Technical Specifications

SpecificationValue
System TypeHyundai-Kia Theta II GDI 150-bar High-Pressure Fuel System
Operating PressureCore Spec
Pump MechanismExhaust Camshaft Lobe Actuated Single-Piston Plunger Pump
Mounting Flange Bolt Torque13 N·m (115 in-lb) flange bolts
Fuel Line Nut Torque28 N·m (21 lb-ft) high-pressure delivery pipe flare nut
Drive InterfaceRoller Tappet Bucket with Hardened Contact Face
Low-Pressure Inlet FittingQuick-Disconnect Barb with Integrated Damper
ManufacturerHyundai Mobis / Kefico (Tier-1 OEM for Hyundai Motor Group)
OEM Service Reference35320-2G700 / 35320-2G740

Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)

Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.

CONTINENTALExact Engine & Chassis Match
35310-2G700
Gasoline Direct Injection (GDI) • 150 bar
🚙 Hyundai Santa Fe Sport (G4KH)
Technical Specifications & Pinout
05

Installation Tips

  1. Low-Pressure Supply Bleed & Battery Disconnect: Remove fuel pump fuse from underhood junction box. Crank engine for 5 seconds to depressurize fuel lines. Disconnect vehicle negative 12V battery terminal.
  2. Engine Beauty Cover & Noise Damper Removal: Unbolt engine cover and pull back the heavy rubber noise shield covering the high-pressure fuel pump on top of the valve cover.
  3. High-Pressure Pipe & Harness Disconnection: Unplug electrical solenoid harness. Use a 17mm line wrench with counter-torque to disconnect high-pressure metal fuel pipe from pump outlet.
  4. Pump Removal & Roller Lifter Tappet Check: Loosen mounting bolts alternately in half-turn increments. Lift pump out and remove the roller tappet. Inspect tappet face and camshaft lobe for wear grooves.
  5. New Pump Installation & Torque Sequence: Lubricate new Viton O-ring and roller tappet with fresh oil. Rotate engine to lowest cam profile. Torque mounting bolts to 13 N·m (115 in-lb) and fuel pipe union nut to 28 N·m (21 lb-ft).
Tips & Warnings:
  • Verify part number 35320-2G700 and the cross references against the vehicle’s EPC before fitting.
  • Torque the pump mounting/hold-down fasteners to 13 N·m and the high-pressure line to 28 N·m.
  • Check for listed DTCs P0300, P0087, P0193, P0089, and P0191 and diagnose the high-pressure fuel system before replacing the pump.
06

Frequently Asked Questions

QWhat part number and cross references identify this pump, and what vehicles does it fit?

This is part number 35320-2G700, a gasoline direct-injection high-pressure fuel pump for Hyundai/Kia 2.0L T-GDI and 2.4L GDI Theta II (G4KH / G4KJ) engines. Cross references are 353202G700, 353202G720, 353202G730, GDP206, HM10014, and 06K127025D. Listed fitment is Hyundai Sonata (G4KH/G4KJ, 2011-2019), Kia Optima (G4KH/G4KJ, 2011-2020), and Hyundai Santa Fe Sport (G4KH/G4KJ, 2013-2018); confirm any other application against the vehicle’s EPC.

QWhich diagnostic trouble codes are listed for this high-pressure fuel pump?

The listed DTCs are P0300, P0087, P0193, P0089, and P0191. Diagnose the high-pressure fuel system and verify the pump before replacement rather than assuming these codes alone confirm a failed pump.

QWhat system pressure and torque values apply to this pump?

The listed system pressure is 150 bar. Use 13 N·m for the mounting/hold-down torque and 28 N·m for the high-pressure line torque.

QCan I reuse the seals, and does this pump require coding or adaptation?

The verified facts do not state whether the seals can be reused or whether coding/adaptation is required. Confirm those points against the vehicle’s EPC before installation and do not guess.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol