Delphi EJBR01701Z
common rail injector
8200240244, 7711135329, 820036518628239294L096PBD1400 bar peak rail pressureProduct Overview
The Delphi EJBR01701Z is an authentic common rail diesel injector calibrated for Renault Megane II and K9K engine applications. Operating at an engineered rail pressure of 1400 bar, this solenoid assembly features the precision 28239294 control valve and L096PBD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR01701Z |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | 🔗 Shared Nozzle (2 assemblies):EJBR01801A |
| Hold Down Torque | 30 N·m |
| High-Pressure Line Torque | 28 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 3 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 30 N·m, then reconnect the high-pressure line and tighten it to 28 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Before fitting EJBR01701Z, confirm the vehicle application and any matching requirements against the EPC or workshop manual.
- Confirm seal and installation details in the workshop data rather than assuming they carry over from the old injector.
- Keep the common-rail system clean and follow the manufacturer's procedure for EJBR01701Z during diagnosis and installation.
Frequently Asked Questions
Will EJBR01701Z fit my Renault Megane, Renault Scenic, or Dacia Logan diesel?
EJBR01701Z is listed for Renault Megane, Renault Scenic, and Dacia Logan diesel applications; confirm the exact vehicle against the EPC or workshop manual before ordering.
What symptoms indicate a failed EJBR01701Z injector?
Symptoms are not listed in the supplied product data; diagnose the vehicle using the manufacturer's workshop procedure before replacing EJBR01701Z.
What should I check before ordering EJBR01701Z?
Confirm the vehicle application, engine family, and current injector identification against the EPC or workshop manual; do not rely on visual similarity alone before ordering EJBR01701Z.
Must the old injector be matched or adapted to the vehicle?
Coding or adaptation requirements are not stated in the supplied data; confirm whether matching is required for the vehicle against the EPC or workshop manual before fitting EJBR01701Z.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.