DELPHI EJBR05102D
Common Rail Injector for Renault Clio III K9K
8200421359, 8200676774, 8200815416, 166001137R28239294L153PBD1600 bar peak rail pressureProduct Overview
The Delphi EJBR05102D is an authentic common rail diesel injector calibrated for Renault Clio III and K9K engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L153PBD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 4 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR05102D |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 30 N·m |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 4 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 30 N·m, then reconnect the high-pressure line and tighten it to 25 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm the engine code and listed fitment for EJBR05102D against the vehicle's EPC before ordering.
- Torque the injector hold-down to 30 N·m and the high-pressure line to 25 N·m.
- Check the listed cross references EJBR03101D, 8200421359, 8200676774, 8200815416 and 166001137R when verifying the old part.
Frequently Asked Questions
Which vehicles is part EJBR05102D listed for?
EJBR05102D is a common-rail diesel injector listed for Renault Clio III 1.5 dCi (K9K 764) 2005-2012, Renault Megane II 1.5 dCi (K9K 724/732) 2005-2008, and Renault Scenic II 1.5 dCi (K9K 732) 2005-2009. It is also listed for Dacia Logan 1.5 dCi (K9K 792/796) 2006-2012 and Dacia Duster 1.5 dCi (K9K 796) 2010-2015. Confirm the engine code and EPC fitment before ordering.
What diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0088 and P0204. Specific symptoms and a test procedure are not stated in the supplied facts; confirm any unlisted diagnostic details against the vehicle's EPC instead of guessing.
Does this injector need coding or adaptation after fitting?
Coding or adaptation requirements are not stated in the supplied facts. Confirm whether coding or adaptation is required against the vehicle's EPC before installation, and do not guess the procedure.
What are the torque values and can I reuse the seals?
Seal reuse is not stated in the supplied facts; confirm it against the vehicle's EPC. The listed mounting/hold-down torque is 30 N·m, the high-pressure line torque is 25 N·m, and the system pressure is 1600 bar for this common-rail diesel injector.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.