DELPHI EJBR01801A
Common Rail Injector for Renault Clio II K9K
8200049873, 8200206565, 8200365186, 16600-00Q0A, 16600-00Q0C28239294L096PBD1400 bar peak rail pressureProduct Overview
The Delphi EJBR01801A is an authentic common rail diesel injector calibrated for Renault Clio II and K9K engine applications. Operating at an engineered rail pressure of 1400 bar, this solenoid assembly features the precision 28239294 control valve and L096PBD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR01801A |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | 🔗 Shared Nozzle (2 assemblies):EJBR01701Z |
| Hold Down Torque | 30 N·m |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 3 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 30 N·m, then reconnect the high-pressure line and tighten it to 25 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Verify part number EJBR01801A and the listed cross references against the vehicle's EPC before installation.
- Torque the injector mounting/hold-down to 30 N·m.
- Confirm the common-rail system pressure is 1400 bar and torque the high-pressure line to 25 N·m.
Frequently Asked Questions
Will part number EJBR01801A fit my vehicle?
EJBR01801A is a common-rail diesel injector listed for the K9K, K9K 700, K9K 702, K9K 704, and K9K 710 engine families. Listed fitments are Renault Clio II 1.5 dCi (K9K 700/704) 2001-2008; Renault Megane II 1.5 dCi (K9K 722) 2002-2008; Renault Kangoo 1.5 dCi (K9K 702/710) 2001-2008; Renault Scenic II 1.5 dCi (K9K 722) 2003-2008; and Nissan Micra (K12) 1.5 dCi (K9K 704) 2003-2010. Confirm the vehicle by EPC before ordering.
Which diagnostic trouble codes are listed for this injector, and what symptoms should I expect?
The verified diagnostic trouble codes for this listing are P0300, P0301, P0087, P0302, and P0304. Specific symptom descriptions are not stated in the supplied facts, so confirm diagnosis against the vehicle's EPC rather than guessing.
Do I need to code or adapt the injector after installation, and can I reuse the old seals?
Coding/adaptation requirements for EJBR01801A are not stated in the supplied facts, so confirm them against the vehicle's EPC rather than assuming. Seal reuse is also not stated; confirm the required seal procedure against the vehicle's EPC.
How can I verify the old injector before ordering a replacement?
Compare the old unit with part number EJBR01801A and the listed cross references: EJBR04001D, 8200049873, 8200206565, 8200365186, 16600-00Q0A, and 16600-00Q0C. Also confirm the engine family and vehicle fitment against the vehicle's EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.