Delphi EJBR01901Z
common rail injector
15310-84A00, 1531084A0028239294L120PBD1400 bar peak rail pressureProduct Overview
The Delphi EJBR01901Z is an authentic common rail diesel injector calibrated for Suzuki Jimny III (FJ) and K9K engine applications. Operating at an engineered rail pressure of 1400 bar, this solenoid assembly features the precision 28239294 control valve and L120PBD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR01901Z |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 30 N·m |
| High-Pressure Line Torque | 28 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 3 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 30 N·m, then reconnect the high-pressure line and tighten it to 28 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm the old injector part number EJBR01901Z and cross references EJBR02401Z, 15310-84A00, and 1531084A00 before ordering.
- Use the specified mounting/hold-down torque of 30 N·m and high-pressure line torque of 28 N·m.
- Check for the listed DTCs P0300, P0087, P0201, P0204, and P0202 during diagnosis.
Frequently Asked Questions
Does this common-rail diesel injector fit my Suzuki?
It is listed for Suzuki Jimny III (FJ) 1.5 DDiS 4WD (K9K 700) (2003-2005) and Suzuki Ignis II 1.5 DDiS (K9K 700) (2003-2006). The engine family is K9K, 1.5 DDiS, and the injector is for a 1400 bar common-rail system. Confirm your vehicle against its EPC before ordering.
What are the mounting and high-pressure line torques for this injector?
Mounting/hold-down torque is 30 N·m. High-pressure line torque is 28 N·m.
What diagnostic trouble codes are listed for this common-rail diesel injector?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0204, and P0202. Use them as diagnostic references for the common-rail diesel injector.
Does this injector require coding or adaptation?
The verified facts do not state a coding or adaptation requirement for this injector. Confirm any required procedure against the vehicle's EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.