Catalog / DENSO / 23209-0P010
DENSO

DENSO 23209-0P010

View Specs
SolenoidGasoline Direct Injection (GDI / HDEV)Euro 6

High Pressure Fuel Injector Toyota Tacoma Highlander Lexus RX350 3.5L 2GR FKS

Reference data for DENSO 23209-0P010 common rail injector · OEM 23209-31090, 23209-39215, 297500-0120 · Application Toyota / Lexus 3.5L V6 2GR-FKS / 2GR-FXS D-4S & 2GR-FE Dual VVT-i
OE REFERENCE23209-31090, 23209-39215, 297500-0120
CONTROL VALVESLIT-NOZZLE DUAL-FAN HIGH-ATOMIZATION DIRECT INJECTION VALVE
NOZZLESlit-Nozzle Dual-Fan Symmetrical Dispersion
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Denso 23209-0P010 (Toyota OE 23209-31090 / 23209-39215 / 297500-0120) is the factory original equipment high-pressure direct fuel injector for Toyota and Lexus 3.5L V6 2GR-FKS D-4S dual-injection engines. Operating at up to 200 bar (2900 psi), it utilizes a specialized slit nozzle creating two fan-shaped sprays aimed at the piston cavity for ultra-clean combustion. Failure triggers rough acceleration hesitation, high-speed power loss, and diagnostic trouble codes P0087 and P0171.

Before You Order

Always verify the OE reference 2320931090, 2320939215, 2975000120 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 23209-0P010 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Toyota Tacoma 3.5LToyota / Lexus 3.5L V6 2GR-FKS / 2GR-FXS D-4S & 2GR-FE Dual VVT-i2016-2023
Toyota Highlander 3.5LToyota / Lexus 3.5L V6 2GR-FKS / 2GR-FXS D-4S & 2GR-FE Dual VVT-i2017-2022
Lexus RX350 3.5LToyota / Lexus 3.5L V6 2GR-FKS / 2GR-FXS D-4S & 2GR-FE Dual VVT-i2016-2022
04

Technical Specifications

SpecificationValue
Injector TypeDenso High-Pressure Solenoid Direct Fuel Injector (DI)
Operating Rail PressureCore Spec
Nozzle Spray GeometryCore Spec
Coil Resistance Value1.7 to 2.1 Ohms at 20°C (Low Impedance Peak-and-Hold)
Fuel Rail Mounting Bolt Torque21 N·m
High Pressure Pipe Flare Nut Torque35 N·m
Tightening Torque35 N·m
Hold Down Torque21 N·m
Primary OEM Reference23209-0P010, 23209-31090, 23209-39215, 23209-31120
Engine Emission ComplianceEuro 6 / LEV III / Tier 3 Bin 30
Standard Industrial Warranty12 Months / Unlimited Mileage

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

DENSOExact Engine & Chassis Match
23100-0P040
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code 2GRFE
Technical Specifications & Pinout
05

Installation Tips

Tools needed: 10mm, 12mm, and 14mm sockets, extensions, and torque wrench, 17mm line flare nut wrench for direct fuel pipe connections, Special Service Tool (SST) for Teflon combustion seal installation and sizing, Slide hammer injector puller adapter for carbon-seized DI injectors, Clean engine oil or assembly lubricant for upper O-ring only

  1. Disconnect negative battery terminal; depressurize fuel system by removing fuel pump fuse and cranking engine for 5 seconds.
  2. Disconnect direct injector electrical wiring harness connectors.
  3. Remove upper intake manifold plenum assembly to access the direct injection fuel rails on cylinder bank 1 and bank 2.
  4. Disconnect high-pressure fuel feed lines from both direct fuel rails.
  5. Remove fuel rail retaining bolts; extract fuel rail and direct injectors from cylinder head carefully.
  6. Extract direct injectors from cylinder head pockets; clean injector bores of all carbon debris using non-abrasive brass tool.
  7. Replace lower white Teflon combustion chamber seal using the expander cone and resizing sleeve; keep Teflon dry.
  8. Replace upper rail O-rings and backup rings; apply light coat of clean engine oil to upper O-rings.
  9. Carefully insert direct injectors into cylinder head ports ensuring guide clips align properly.
  10. Position fuel rail over injectors; install rail mounting bolts and torque evenly to 21 N·m.
  11. Hand-start high-pressure fuel pipe union nuts; torque high-pressure fuel line nuts to 35 N·m.
  12. Reassemble intake manifold plenum with new gaskets; reconnect battery and cycle ignition on 3 times to inspect for fuel leaks.
Tips & Warnings:
  • Teflon Seal Protection: The lower Teflon seal expands when heated in combustion chamber; never touch or grease the seal during installation to avoid combustion blowby.
  • Rail Torque Symmetry: Tighten fuel rail bolts gradually in three equal passes across both cylinder banks to ensure uniform injector seating depth.
06

Frequently Asked Questions

QWhat are the primary symptoms when 23209-0P010 fails?

Primary symptoms include extended cold engine cranking, severe hesitation under wide-open throttle, rough idle RPM fluctuation, and Diagnostic Trouble Codes P0087 (Fuel Rail/System Pressure Too Low), P0089 (Fuel Pressure Regulator Performance), or P0300 (Random/Multiple Cylinder Misfire).

QWhat is the exact tightening torque for 23209-0P010?

The holding flange mounting torque is 21 N·m, and the high-pressure fuel pipe union nut must be torqued to 35 N·m.

QCan I reuse the seals when replacing 23209-0P010?

No. All high-pressure fuel seals, including Viton O-rings and combustion chamber Teflon rings, are strictly single-use. Reusing compressed seals will cause pressurized fuel leaks or combustion blowby into the cylinder head.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol