BOSCH AG9Z-9350-B
High Pressure Fuel Pump Ford Edge Fusion Focus ST Taurus 2.0L EcoBoost 0261520152
LR025599, 0261520152, 0261520151, GDP204, HM10008--150 bar peak rail pressureProduct Overview
The BOSCH AG9Z-9350-B is a factory precision fuel injection component engineered specifically for the Ford 2.0L EcoBoost GTDI & Land Rover 2.0 Si4 Turbo DOHC. Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 150 bar (2175 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0087, P0088, P0171, P0300 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Always verify the part number AG9Z-9350-B and Continental VDO marking on the existing high-pressure common-rail pump before ordering; confirm the pump application matches your engine before unsealing the packaging.
Vehicle & Engine Fitment
Technical Specifications
| Specification | Value |
|---|---|
| sku | AG9Z-9350-B |
| brand | BOSCH |
| manufacturer_code | 0261520152 |
| pressure_rating | 150 bar (2175 psi) |
| torque_flange | 13 N-m (115 lb-in) |
| torque_line | 28 N-m (21 lb-ft) |
| engine_family | Ford 2.0L EcoBoost GTDI & Land Rover 2.0 Si4 Turbo DOHC |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Fit new seals before installing the pump.
- Lubricate the pump drive interface with clean engine oil before fitting.
- Install the high-pressure pump and align the drive correctly.
- Tighten the mounting fasteners evenly in a criss-cross pattern.
- Hand-thread the high-pressure fuel line fittings, then tighten them to specification.
- Prime the fuel circuit before starting the engine.
- Check the fuel circuit for leaks after priming.
- Start the engine and recheck for leaks.
- Work with a clean fuel system, use new seals, confirm the timing belt/chain or camshaft drive engages correctly, prime the fuel circuit fully, and inspect for leaks before and after the first start.
- Do not reuse seals or sealing washers.
Frequently Asked Questions
Will this AG9Z-9350-B pump fit my vehicle?
This AG9Z-9350-B gasoline direct-injection high-pressure fuel pump is listed for Ford 2.0L & 2.3L EcoBoost DOHC 16V GTDI Twin-Scroll Turbo applications: Mustang 2.3 EcoBoost (2015-2023), Focus RS (2016-2018), and Explorer 2.3 (2016-2023). Confirm exact fitment against the vehicle’s EPC before ordering.
What diagnostic trouble codes are listed for this high-pressure fuel pump?
The verified diagnostic trouble codes listed are P0300, P0087, P0193, P0089, and P0191. Confirm the fault path against the vehicle’s service information during diagnosis.
Does this high-pressure fuel pump need coding or adaptation after installation?
No coding or adaptation requirement is stated in the verified facts for this pump. Confirm any programming or adaptation requirements against the vehicle’s EPC or service information before installation.
Can I reuse the seals, and what are the mounting and line torque values?
Seal reuse is not stated in the verified facts, so it must be confirmed against the vehicle’s EPC or service information. The listed mounting/hold-down torque is 13 N·m, and the high-pressure line torque is 28 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.