BOSCH CJ5Z-9350-B
High Pressure Fuel Pump Ford Escape Explorer Focus ST Fusion Edge 2.0L EcoBoost 0261520140
0261520140, 0261520141, LR025599, GDP204INTEGRATED HIGH-SPEED DIGITAL FLOW CONTROL SOLENOID-150 bar peak rail pressureProduct Overview
The Bosch CJ5Z-9350-B (Bosch engineering reference 0261520140, Ford superseded number AG9Z-9350-B, Land Rover LR025599) is the original equipment mechanical high-pressure fuel pump (HPFP) engineered for Ford's 2.0-liter EcoBoost turbocharged 4-cylinder engine. Generating fuel rail pressures up to 150 bar (2175 psi), this camshaft-actuated single-plunger pump powers high-volume enthusiast and utility platforms including the Ford Focus ST, Escape, Explorer, Fusion, Edge, and Land Rover Range Rover Evoque. High-mileage vehicles frequently experience power loss under boost, acceleration stutter, extended morning cranking times, and diagnostic trouble code P0087 (Fuel Rail/System Pressure Too Low). The root causes typically involve roller tappet wear, sticking digital volume control metering valves, or internal plunger shaft seal wear. When internal seals deteriorate, pressurized fuel washes into the cylinder head, diluting engine oil and threatening turbocharger bearings. Correct replacement requires strict adherence to OEM workshop practices. The mounting flange bolts must be drawn down alternately and tightened to 13 N·m (115 in-lb), while the high-pressure steel delivery line flare nut requires 28 N·m (21 lb-ft). Technicians must inspect the roller tappet bucket and change engine oil and filter immediately if fuel dilution is verified.
Always verify the OE reference LR025599, GDP204 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. CJ5Z-9350-B needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Ford Focus / Escape | Ford 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo) | 2013-2019 |
| Ford Fusion / Explorer | Ford 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo) | 2012-2020 |
| Land Rover Range Rover Evoque | Ford 2.0L & 2.3L EcoBoost (DOHC 16V GTDI Twin-Scroll Turbo) | 2012-2017 |
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Ford EcoBoost 150-bar High-Pressure Direct Injection System |
| Operating PressureCore Spec | |
| Pump Mechanism | Camshaft Multi-Lobe Actuated Single-Piston Plunger Pump |
| Mounting Flange Bolt Torque | 13 N·m (115 in-lb) flange bolts |
| Fuel Line Nut Torque | 28 N·m (21 lb-ft) high-pressure delivery pipe flare nut |
| Drive Interface | Roller Tappet Bucket Lifter with Hardened Surface |
| Flow Control Solenoid | Integrated 12V Pulse-Width Modulated Solenoid Actuator |
| Manufacturer | Bosch (Tier-1 OEM for Ford Motor Company) |
| Bosch Production Number | 0261520140 / 0261520141 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- EcoBoost Fuel Pressure Depressurization: Remove fuel pump fuse from engine compartment fuse box. Crank engine until it stalls to deplete rail pressure, then disconnect negative battery cable.
- Air Cleaner Duct & Acoustic Insulator Removal: Disconnect turbo intake pipe and unclip acoustic foam noise shield surrounding the fuel pump on the side of the cylinder head.
- High-Pressure Metal Fuel Delivery Line Removal: Unscrew the steel fuel pipe flare nut using a backup wrench on the pump fitting. Disconnect lower rail connection and discard single-use pipe.
- Pump Removal & Roller Lifter Tappet Inspection: Evenly loosen the two mounting bolts in half-turn increments to relieve spring tension. Remove pump and inspect internal roller tappet for flat spots.
- New Pump Installation & Torque Sequence: Lubricate new O-ring and roller tappet with fresh motor oil. Turn engine until cam is on base circle. Torque mounting bolts to 13 N·m (115 in-lb) and fuel pipe nut to 28 N·m (21 lb-ft).
- Always replace the roller tappet: A worn or flat-spotted roller tappet will destroy the exhaust camshaft driving lobe, requiring complete camshaft replacement.
- Never reuse single-use high-pressure fuel pipe: Ford factory service directives require replacement of the flared steel delivery pipe whenever loosened.
- Verify low-pressure lift pump delivery: A weak tank lift pump (under 50 psi) starves the HPFP, causing cavitation and false pump failure codes.
- Inspect engine oil for fuel odor: A leaking pump plunger seal allows raw fuel into the cylinder head, diluting oil and risking turbocharger bearing failure.
Frequently Asked Questions
What vehicles and engine family does part CJ5Z-9350-B fit?
This is a gasoline direct-injection high-pressure fuel pump listed for the Ford 2.0L & 2.3L EcoBoost DOHC 16V GTDI Twin-Scroll Turbo engine family. Listed fitment is Ford Focus / Escape 2013-2019, Ford Fusion / Explorer 2012-2020, and Land Rover Range Rover Evoque 2012-2017. Confirm vehicle fitment against the vehicle’s EPC before ordering.
What diagnostic trouble codes are listed, and what symptoms should I expect from a failed unit?
The diagnostic trouble codes listed for this high-pressure fuel pump are P0300, P0087, P0193, P0089, and P0191. Specific symptoms are not stated in the provided facts, so confirm diagnosis against the vehicle’s EPC.
What are the mounting and high-pressure line torque specs, and what system pressure is listed?
The mounting / hold-down torque is 13 N·m, and the high-pressure line torque is 28 N·m. The listed system pressure is 150 bar.
How can I verify the old pump and what cross references should I check?
The part number is CJ5Z-9350-B, with cross references CJ5Z9350B, 0261520140, 0261520141, LR025599, GDP204, and 13517588879. Use these references to verify the old pump, and confirm fitment against the vehicle’s EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.