KEIHIN 16700-59B-004
High Pressure Fuel Pump Honda Civic CR V Accord 1.5L Turbo Earth Dreams L15B7 16700 59B 014
16700-59B-014, GDP209, HM10025INTEGRATED HIGH-SPEED SPILL CONTROL SOLENOID VALVE-200 bar peak rail pressureProduct Overview
The Keihin 16700-59B-004 (superseded by 16700-59B-014) mechanical high-pressure fuel pump (HPFP) provides direct fuel metering on Honda's 1.5-liter Earth Dreams turbo engines (L15B7, L15BA, L15BE). Driven by the exhaust camshaft, this pump elevates low-pressure tank fuel (4-6 bar) up to an operational peak of 200 bar (2900 psi). The pump incorporates an integrated electromagnetic spill control valve that times the closing point during the plunger compression stroke, delivering precise micro-doses of pressurized fuel to the direct injection rail.
Always verify the OE reference 1670059B014, GDP209, HM10025 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 16700-59B-004 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Operating PressureCore Spec | |
| Pump Technology | Single Plunger Mechanical Camshaft-Driven HPFP |
| Flow Control | High-Speed Electromagnetic Spill Valve |
| Mounting Flange Torque | 12 N·m |
| High Pressure Line Torque | 28 N·m |
| Drive Type | Exhaust Camshaft Tri-Lobe Drive with Roller Tappet |
| Fuel Type | Gasoline Direct Injection (GDI / Earth Dreams) |
| OE Cross References | 16700-59B-004, 1670059B004, 16700-59B-014, 1670059B014, GDP209 |
| Failure Symptoms | Crankcase oil level rise (fuel dilution), pungent gasoline odor in oil, long warm crank, P0087 |
| Diagnostic Test | HDS Live Data: compare Target FRP vs Actual FRP across 1500-6000 RPM boost transitions |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- De-energize low-pressure fuel pump relay and run engine until stall to relieve fuel pressure.
- Remove engine acoustic beauty cover and disconnect spill control valve harness connector.
- Counter-hold pump discharge fitting and loosen high-pressure steel fuel pipe flare nut.
- Remove the mounting bolts in small alternating turns to release internal spring tension safely.
- Extract pump assembly and inspect cylinder head roller tappet for scoring, wear, or seizure.
- Replace sealing O-ring and apply a coat of fresh engine oil prior to inserting into cylinder head.
- Tighten mounting flange bolts progressively in an X-pattern to exactly 12 N·m.
- Hand-thread high-pressure pipe nut to ensure zero cross-threading, then torque to 28 N·m.
- Reconnect harness, cycle key 3 times to prime low-pressure feed, and verify zero fuel leakage.
- Torque the pump mounting/hold-down fasteners to 12 N·m.
- Torque the high-pressure line to 28 N·m.
- Verify the part number 16700-59B-004 and listed cross references against the vehicle’s EPC before installation.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Honda Civic or CR-V?
It is listed for Honda Civic (FC/FK) 2016-2021 and Honda CR-V (RW) 2017-2022 with the Honda 1.5L Earth Dreams VTEC Turbo & i-VTEC engine family (L15B7 / L15BA / L15BE / L15B2). Confirm fitment against the vehicle’s EPC if your application is not exactly one of these.
What diagnostic trouble codes are associated with this pump, and what symptoms should I expect?
The verified DTCs for this listing are P0300, P0087, P0193, P0089, and P0191. No symptom list or service-life figure is provided in the verified facts; diagnose the vehicle rather than guessing.
Do I need to code or adapt this high-pressure fuel pump, and can I reuse the seals?
No coding/adaptation requirement or seal-reuse guidance is stated in the verified facts; confirm these against the vehicle’s EPC or service information. Do not guess.
How do I verify the old pump and what torque values apply?
Verify by part number 16700-59B-004 and the listed cross references: 1670059B004, 1670059B014, GDP209, HM10025, and 1601059B315. Mounting/hold-down torque is 12 N·m; high-pressure line torque is 28 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.