BOSCH 35320-2G740
High Pressure Fuel Pump Hyundai Sonata Santa Fe Kia K5 Sorento 2.0T Theta II Turbo
GDP228, 0261520147--150 bar peak rail pressureProduct Overview
The 35320-2G740 is an original equipment (BOSCH) precision component engineered specifically for the Hyundai/Kia 2.0L Turbocharged GDI DOHC 16V I4 (Theta II 2.0T / G4KH). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P0016.
Always verify the OE reference GDP228 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 35320-2G740 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 35320-2G740 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Hyundai/Kia 2.0L Turbocharged GDI DOHC 16V I4 (Theta II 2.0T / G4KH) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P0016 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify the system pressure specification is 150 bar before testing.
- Tighten the pump mounting/hold-down fasteners to 13 N·m.
- Tighten the high-pressure line to 30 N·m.
Frequently Asked Questions
Will part 35320-2G740 fit my Hyundai Sonata, Kia Optima, or Hyundai Santa Fe Sport?
Part 35320-2G740 is listed for Hyundai Sonata G4KH/G4KJ 2011-2019, Kia Optima G4KH/G4KJ 2011-2020, and Hyundai Santa Fe Sport G4KH/G4KJ 2013-2018. Cross references include 353202G740, GDP228, 0261520147, 353102G700, 353202G700, and 353202G720. Confirm the exact engine code and model year against the vehicle’s EPC before ordering.
What fault codes can indicate a problem with this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. The facts provided do not list specific symptoms, so confirm diagnosis and symptom checks against the vehicle’s EPC or service information.
Does this high-pressure fuel pump need coding or adaptation after installation?
The provided facts do not state a coding or adaptation requirement for 35320-2G740. Confirm coding/adaptation requirements against the vehicle’s EPC or service information before installation.
Can I reuse the mounting seals and high-pressure line?
The facts do not state whether the mounting seals or high-pressure line can be reused. Confirm seal and line reuse requirements against the vehicle’s EPC or service information, and observe the listed mounting torque of 13 N·m and high-pressure line torque of 30 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.