BOSCH 35320-2GGA0
High Pressure Fuel Pump Hyundai Sonata Santa Fe Kia Optima Sorento 2.4L GDI Theta II
0261520307, HM10027, GDP211, 35320-2GGA1, 0261520308--200 bar peak rail pressureProduct Overview
The 35320-2GGA0 is an original equipment (BOSCH) precision component engineered specifically for the Hyundai-Kia 2.4L GDI & 2.0 T-GDI Theta II DOHC 16V. Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference HM10027, GDP211, 353202GGA1 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 35320-2GGA0 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 35320-2GGA0 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Hyundai-Kia 2.4L GDI & 2.0 T-GDI Theta II DOHC 16V |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the engine code and model year against the vehicle EPC before installing part number 35320-2GGA0.
- Tighten the mounting/hold-down fasteners to 13 N·m and the high-pressure line to 30 N·m.
- Check for the listed DTCs P0300, P0087, P0193, P0089, and P0191 during diagnosis.
Frequently Asked Questions
Will this pump fit my Hyundai/Kia, and how do I verify the old part?
Part number 35320-2GGA0 is a gasoline direct-injection high-pressure fuel pump listed for Hyundai Sonata G4KH/G4KJ (2011-2019), Kia Optima G4KH/G4KJ (2011-2020), and Hyundai Santa Fe Sport G4KH/G4KJ (2013-2018). Cross references include 353202GGA0, 0261520307, HM10027, GDP211, 353202GGA1, and 0261520308. Match the old pump markings and confirm engine code/year against the vehicle EPC before ordering.
What diagnostic trouble codes are associated with this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. If a code or symptom is not listed here, confirm it against the vehicle's service information and EPC instead of guessing.
Does this high-pressure fuel pump require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the provided facts. Confirm programming/adaptation steps against the vehicle manufacturer's service information and EPC for the exact G4KH/G4KJ application.
What are the mounting and high-pressure line torque values, and can I reuse the seals?
Mounting/hold-down torque is 13 N·m, and high-pressure line torque is 30 N·m. Seal reuse is not stated in the provided facts, so confirm seal and hardware replacement against the vehicle EPC/service information. Do not guess additional torque values.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.