BOSCH 35320-2GTA0
High Pressure Fuel Pump Hyundai Sonata Turbo Santa Fe Kia Optima Sorento 2.0T Theta II 0261520311
0261520312, HM10028, GDP212, 35320-2G700, 0261520311--200 bar peak rail pressureProduct Overview
The 35320-2GTA0 is an original equipment (BOSCH) precision component engineered specifically for the Hyundai-Kia 2.0L Turbo GDI Theta II DOHC 16V. Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference HM10028, GDP212, 353202G700 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 35320-2GTA0 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 35320-2GTA0 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Hyundai-Kia 2.0L Turbo GDI Theta II DOHC 16V |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Torque the mounting/hold-down fasteners to 13 N·m.
- Torque the high-pressure line to 30 N·m.
- Verify part number 35320-2GTA0, engine code G4KH or G4KJ, and EPC fitment before installation.
Frequently Asked Questions
Will this pump fit my Hyundai Sonata, Kia Optima, or Hyundai Santa Fe Sport?
It is listed for Hyundai Sonata (2011-2019), Kia Optima (2011-2020), and Hyundai Santa Fe Sport (2013-2018) with the Hyundai / Kia 2.0L T-GDI & 2.4L GDI Theta II engine family (G4KH / G4KJ). The part number is 35320-2GTA0, and cross references include 353202GTA0, 0261520312, HM10028, GDP212, 353202G700, and 0261520311. Confirm the vehicle’s engine code and EPC listing before ordering.
What symptoms or codes point to a failed high-pressure fuel pump?
For this listing, the diagnostic trouble codes given are P0300, P0087, P0193, P0089, and P0191. The supplied facts do not list other failure symptoms or a diagnostic test procedure, so confirm diagnosis against the vehicle’s service information or EPC rather than guessing.
Does this pump need coding/adaptation, and can I reuse the seals?
The supplied facts do not state whether coding or adaptation is required, or whether the seals can be reused, for part 35320-2GTA0. Confirm both points against the vehicle’s EPC or service information before installation.
How can I verify the old pump and what torque values should I use?
Compare the old pump’s part number with 35320-2GTA0 and the listed cross references 353202GTA0, 0261520312, HM10028, GDP212, 353202G700, and 0261520311, then confirm the engine code and fitment against the vehicle EPC. The mounting/hold-down torque is 13 N·m and the high-pressure line torque is 30 N·m; system pressure is 200 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.