Catalog / KEIHIN / 16450-R40-003
KEIHIN

KEIHIN 16450-R40-003

View Specs
SolenoidMulti-Point Port Fuel Injection (MPI / EV14)Euro 5

Multi Port Fuel Injector Honda Accord CR V Civic Si Acura TSX 2.4L i VTEC K24Z 16450 R40 A01

Reference data for KEIHIN 16450-R40-003 common rail injector · OEM 16450-R40-A01, FJ1045, 842-12365 · Application Honda 2.4L Earth Dreams & K-Series i-VTEC (K24W1 / K24W2 / K24Z / K24A)
OE REFERENCE16450-R40-A01, FJ1045, 842-12365
CONTROL VALVE10-HOLE PRECISION MULTI-DISPERSAL MICRO-DROPLET ATOMIZATION DIRECTOR
NOZZLE-
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

The Keihin 16450-R40-003 (superseding part number 16450-R40-A01, aftermarket cross-reference FJ1045) is the original equipment multi-port fuel injector engineered for Honda's acclaimed 2.4-liter K-series i-VTEC inline-four engines (K24Z2, K24Z3, K24Z6, and K24Z7). Delivering a calibrated 310 cc/min static flow rate at 3.8 bar (55 psi) with an advanced 10-hole atomization plate, this high-impedance fuel injector delivers precision fueling across millions of high-volume passenger vehicles, including the Honda Accord Mk8 (2008-2012), CR-V Mk3/Mk4 (2010-2014), Civic Si (2012-2015), Crosstour, and Acura TSX (CU2) and ILX. Over extended engine run times, heavy fuel fractions and deposit varnish adhere to the 10 micro-orifices. This restriction disturbs the wide-angle spray cone into unequal fuel streams, leading to fuel puddling in intake runners. Operational symptoms manifest as cold engine extended cranking, intermittent engine shudder at idle with A/C engaged, sluggish throttle response, and diagnostic trouble codes P0300 (Random/Multiple Cylinder Misfire), specific cylinder misfires (P0301 through P0304), and lean air-fuel ratio code P0171 (System Too Lean Bank 1). Professional replacement follows Honda workshop standards. Technicians must renew both the upper Viton fuel rail O-rings and lower intake manifold vibration cushions, lubricating seals with fresh engine oil. The fuel rail securing nuts require 12 N·m (106 in-lb). Confirming smooth injector rotation prior to final assembly ensures 100% sealing integrity against high fuel pressures.

Before You Order

Always verify the OE reference 16450R40A01, FJ1045, 84212365 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16450-R40-003 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Honda Accord Mk8 / CR-VHonda 2.4L Earth Dreams & K-Series i-VTEC (K24W1 / K24W2 / K24Z / K24A)2008-2014
Acura TSX CU2Honda 2.4L Earth Dreams & K-Series i-VTEC (K24W1 / K24W2 / K24Z / K24A)2009-2014
Honda Civic SiHonda 2.4L Earth Dreams & K-Series i-VTEC (K24W1 / K24W2 / K24Z / K24A)2012-2015
04

Technical Specifications

SpecificationValue
System TypeHonda PGM-FI Multi-Point Programmed Electronic Fuel Injection
Operating Fuel Pressure3.8 bar (55 psi / 380 kPa regulated fuel rail pressure)
Static Fuel Flow Rate310 cc/min @ 3.5 bar (29.5 lb/hr) calibrated delivery
Electrical Resistance10.0 - 11.6 Ohms @ 20°C (High-Impedance Saturated Solenoid)
Spray Geometry10-Hole Precision Wide-Angle Multi-Orifice Micro-Atomization
Fuel Rail Mounting Nut Torque12 N·m (106 in-lb / 8.8 lb-ft) M8 flange nuts
Fuel Pulsation Damper Locknut22 N·m (16 lb-ft) threaded rail damper fitting
Seals ArchitectureUpper Viton Fluorocarbon O-Ring & Lower Resilient Vibration Grommet
ManufacturerKeihin Corporation (Tier-1 OEM for Honda Motor Co.)
Manufacturer Part Number16450-R40-003 / 16450-R40-A01

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

KEIHINExact Engine & Chassis Match
16790-5A2-A01
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code K24A
Technical Specifications & Pinout
05

Installation Tips

  1. PGM-FI Fuel System Depressurization: Remove PGM-FI main fuel pump fuse (Fuse 15A) from interior under-dash fuse box. Crank engine until it stalls to exhaust line pressure, then disconnect negative battery terminal.
  2. Engine Decorative Cover & Wiring Harness Bracket Removal: Remove engine i-VTEC plastic intake manifold cover. Unbolt fuel rail wiring harness bracket bolts (10mm) and disconnect electrical plugs from each injector.
  3. Quick-Connect Fuel Supply Hose Disconnection: Release the plastic quick-disconnect retainer clip on the fuel rail supply pipe. Pull line off fuel rail and catch fuel drips with shop rags.
  4. Fuel Rail Securing Fasteners Removal & Injector Extraction: Remove two 10mm fuel rail mounting nuts. Gently wiggle fuel rail straight back from the intake manifold. Remove injectors from rail sockets and extract lower manifold cushions.
  5. New O-Ring Lubrication, Installation & Sequence Torquing: Coat new upper O-rings and lower rubber vibration cushions with clean engine oil. Push injectors into fuel rail with a gentle twist. Torque rail mounting nuts to 12 N·m (106 in-lb).
Tips & Warnings:
  • Mandatory lower manifold cushion renewal: Never reuse hardened lower manifold rubber cushions; hardened rubber permits unmetered air intrusion, causing persistent P0171 lean codes.
  • Verify injector free rotation: After torquing the fuel rail nuts, verify that each injector rotates smoothly between fingers to ensure O-rings are seated without twisting.
  • Never use silicone sealants: Lubricate O-rings strictly with fresh engine oil or spindle oil; silicone will permanently contaminate lambda sensors.
  • Prime fuel circuit prior to cranking: Turn ignition switch to ON (Position II) for 3 seconds twice without cranking to pressurize the rail and check for leaks.
06

Frequently Asked Questions

QWill part number 16450-R40-003 fit my Honda or Acura?

It is listed for Honda Accord Mk8 / CR-V (2008-2014), Acura TSX CU2 (2009-2014), and Honda Civic Si (2012-2015). It is also listed for the Honda 2.4L Earth Dreams & K-Series i-VTEC engine family (K24W1 / K24W2 / K24Z / K24A). Confirm fitment by VIN against the vehicle's EPC before ordering.

QWhat diagnostic trouble codes are listed for this multi-point fuel injector?

The listing references DTCs P0300, P0301, P0087, P0302, and P0304. Use these as diagnostic references only and confirm the actual fault against the vehicle's service information; no additional symptom or failure-mode details are stated in the verified facts.

QWhat system pressure and installation torques apply to 16450-R40-003?

The listed system pressure is 4 bar. The mounting / hold-down torque is 12 N·m, and the high-pressure line torque is 12 N·m. Confirm any additional procedure details against the vehicle's EPC/service information.

QDoes this injector need coding or adaptation, and can I reuse the seals?

Coding/adaptation requirements and seal reuse are not stated in the verified facts, so they must be confirmed against the vehicle's EPC or service information. To verify the old unit, compare part number 16450-R40-003 and cross references 16450R40003, 16450R40A01, FJ1045, 84212365, 160105PA305, and 164505LAA01.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol