KEIHIN 16010-5A2-A52
Direct Fuel Injector Kit Honda Accord CR V 2.4L Earth Dreams K24W K24W1
16010-5A2-A51, 16010-5A2-A50, 16010-5A2-305, 06160-5A2-A52, FJ1217--200 bar peak rail pressureProduct Overview
The KEIHIN 16010-5A2-A52 is a factory precision fuel injection component engineered specifically for the Honda 2.4L Earth Dreams i-VTEC DOHC 16V K24W1 / K24W2. Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 200 bar (2900 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0300, P0301, P0302, P0171 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Always verify the OE reference 160105A2A51, 160105A2A50, 160105A2305, 061605A2A52 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16010-5A2-A52 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| sku | 16010-5A2-A52 |
| brand | KEIHIN |
| manufacturer_code | 16010-5A2-A52 |
| pressure_rating | 200 bar (2900 psi) |
| torque_flange | 12 N-m (106 lb-in) |
| torque_line | 12 N-m (106 lb-in) |
| engine_family | Honda 2.4L Earth Dreams i-VTEC DOHC 16V K24W1 / K24W2 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Always replace single-use high-pressure fuel lines and Teflon/copper sealing washers before installation.
- Lubricate the pump roller tappet or injector O-rings with clean engine oil before guiding into place.
- Tighten mounting flange fasteners in an even criss-cross pattern to 12 N-m (106 lb-in).
- Hand-thread fuel rail fittings first, then torque high-pressure flare nuts to 12 N-m (106 lb-in) using a calibrated crowfoot wrench.
- Cycle the low-pressure fuel pump multiple times and perform a physical leak inspection before engine ignition.
- Confirm the exact engine code and model year against the vehicle EPC before ordering.
- Compare the old injector with part number 16010-5A2-A52 and cross references 160105A2A52, 160105A2A51, 160105A2A50, 160105A2305, 061605A2A52, and FJ1217 before replacement.
- Torque the mounting/hold-down and high-pressure line to 12 N·m.
Frequently Asked Questions
Will this gasoline direct-injection injector, part number 16010-5A2-A52, fit my Honda or Acura?
It is listed for Honda Accord Mk8 / CR-V with K24W1, K24W2, K24Z, or K24A (2008-2014), Acura TSX CU2 with those engines (2009-2014), and Honda Civic Si with those engines (2012-2015). Confirm the exact engine code and model year against the vehicle EPC before ordering, because no other applications are stated in the verified facts.
What symptoms or DTCs may point to a failed unit, and what service life should I expect?
The verified facts list DTCs P0300, P0301, P0087, P0302, and P0304 but do not state specific symptoms. Expected service life is not stated, so confirm it against the vehicle EPC instead of guessing.
Do I need coding or adaptation after installing this injector?
Coding or adaptation requirements are not stated in the verified facts. Confirm them against the vehicle EPC before installation instead of guessing.
What are the torque and pressure specifications, and can I reuse the seals?
System pressure is 200 bar, mounting/hold-down torque is 12 N·m, and high-pressure line torque is 12 N·m. Seal reuse is not stated in the verified facts, so confirm it against the vehicle EPC before reassembly.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.