DENSO PE01-13-350B
High Pressure Fuel Pump Mazda 3 Mazda 6 CX 5 CX 9 2.0L 2.5L SkyActiv G PY01 13 35Z
PE01-13-350A, PY01-13-35Z, PE01-13-350, GDP720, HM10061INTEGRATED HIGH-SPEED DIGITAL SPILL VALVE CONTROL SOLENOID-200 bar peak rail pressureProduct Overview
The Denso PE01-13-350B (superseding part number PE01-13-350A, interchangeable with PY01-13-35Z and aftermarket references GDP720 and HM10061) is the genuine original equipment high-pressure mechanical fuel pump engineered for Mazda's award-winning 2.0-liter (PE-VPS) and 2.5-liter (PY-VPS / PY-VPTS) SkyActiv-G direct injection engine family. Capable of generating up to 200 bar (2,900 psi) of regulated fuel rail pressure, this single-plunger pump is standard equipment on the Mazda 3 (2014-2023), Mazda 6 (2014-2021), CX-5 (2013-2024), CX-9 (2016-2023), CX-30, and MX-5 Miata ND.
Always verify the original manufacturer reference stamped on your component before ordering. For PE01-13-350B, inspect matching OE cross-references and ensure related high-pressure seals, followers, or grommets are renewed during service.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Mazda SkyActiv-G Ultra-High Compression 200-Bar Direct Injection |
| Operating Fuel Rail PressureCore Spec | |
| Camshaft Drive System | Exhaust Camshaft Lobes via Hardened Reciprocating Roller Tappet |
| Pressure Regulation Mechanism | Integrated Fast-Response Spill Control Solenoid Valve |
| Pump Flange Mounting Fasteners | 20 N·m (15 lb-ft) tightened progressively in alternating turns |
| High-Pressure Flare Nut Tube | 28 N·m (21 lb-ft) rigid high-pressure line to stainless rail |
| Internal Piston Plunger Stroke | 7.0 mm stroke with diamond-like carbon (DLC) wear barrier |
| Compatibility | Engineered for 13.0:1 and 14.0:1 ultra-high static compression engines |
| Manufacturer | Denso Corporation (Tier-1 OEM for Mazda Motor Corporation) |
| Production Code | Denso Japan / Mazda PE01-13-350B |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Low & High Pressure Fuel Depressurization: Disconnect the 15A fuel pump fuse from the engine compartment fuse block. Crank engine until it fails to start, exhausting residual high pressure from the fuel rail, then disconnect battery ground.
- Air Cleaner Housing & Throttle Body Duct Clearance: Unfasten the engine intake duct and air cleaner box assembly to obtain clean visual and physical clearance above the cylinder head where the high-pressure pump is mounted.
- Spill Valve Electrical Connector & Fuel Line Disconnection: Unclip wiring harness from the digital spill valve. Use a backed-up flare nut wrench (17mm) to unthread high-pressure pipe flare nut slowly with protective rags around the fitting.
- Pump Fasteners Loosening & Cam Tappet Assessment: Back out mounting bolts in alternating half-turns to release internal plunger spring load squarely. Extract the pump and remove internal roller tappet to check for wear or roller binding.
- Flange Seal Lubrication, Seating & Precise Torquing: Lubricate new Viton O-ring with fresh engine oil. Seat pump into cylinder head bore squarely and torque mounting bolts in alternating sequence to 20 N·m (15 lb-ft). Torque high-pressure pipe flare nut to 28 N·m (21 lb-ft).
- Torque the pump mounting/hold-down to 20 N·m.
- Torque the high-pressure fuel line to 28 N·m.
- Verify PE01-13-350B and its listed cross references before ordering.
Frequently Asked Questions
Will part number PE01-13-350B fit my Mazda?
It is listed for Mazda 3/CX-30 and Mazda 6/CX-5 with PE-VPS, PY-VPS or PY-VPTS engines from 2014-2024, and for Mazda CX-9/CX-5 from 2016-2023 and MX-5 Miata ND from 2016-2023. Confirm the exact engine code and model year against the vehicle EPC before ordering.
Which diagnostic trouble codes are listed for this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089 and P0191. Use these codes with the vehicle service information; no additional symptom or diagnostic details are stated for PE01-13-350B.
What are the mounting and high-pressure line torque specifications?
Mounting/hold-down torque is 20 N·m, and high-pressure line torque is 28 N·m. The pump is a gasoline direct-injection high-pressure fuel pump with a listed system pressure of 200 bar.
Does this pump require coding or adaptation after installation?
No coding or adaptation requirement is stated in the listed facts for PE01-13-350B. Confirm any programming or adaptation procedure against the vehicle EPC/service information before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.