BOSCH 13517588879
High Pressure Fuel Pump BMW 320i 328i 528i X1 X3 X5 Z4 2.0L Turbo N20 N26 0261520141
7588879, 0261520141, 0261520142, 13518604229, 8604229, 13517630644, 7630644INTEGRATED HIGH-SPEED DIGITAL FUEL QUANTITY CONTROL VALVE-200 bar peak rail pressureProduct Overview
The Bosch 13517588879 (Bosch engineering reference 0261520141, superseded by 13518604229) is the authentic Tier-1 original equipment high-pressure mechanical fuel pump designed for BMW's ubiquitous N20 and N26 2.0-liter TwinPower Turbo 4-cylinder engines. Operating at up to 200 bar (2900 psi), this camshaft-actuated single-plunger pump provides direct fuel delivery to models across the BMW lineup, including the 320i, 328i (F30), 528i (F10), X1 (E84), X3 (F25), and 428i (F32). High-mileage N20 engines frequently present drivability issues accompanied by the dreaded 'Drivetrain Malfunction - Drive Moderately' cluster warning. Characteristic fault codes include P0087 (Fuel Rail/System Pressure - Too Low), BMW shadow codes 11A002 (Fuel high pressure, cold start: Pressure too low) and 110001 (Fuel high pressure: Injection rail pressure too low). These symptoms arise from internal piston seal fatigue, electric metering solenoid valve failure, or severe roller tappet wear. Installation of the replacement HPFP requires strict adherence to BMW technical specifications. Mounting flange bolts must be drawn down evenly to 13 N·m (115 in-lb), and the high-pressure steel outlet pipe tightened to 30 N·m (22 lb-ft). Technicians must inspect the camshaft driving lobe, replace the roller tappet, and verify that crankcase engine oil is free of fuel dilution to protect turbocharger and rod bearings.
Always verify the OE reference 7588879, 13518604229, 8604229, 13517630644 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 13517588879 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | BMW High Precision Direct Injection (HPI) 200-bar System |
| Operating PressureCore Spec | |
| Pump Mechanism | Camshaft Multi-Lobe Driven Single-Piston Plunger Pump |
| Mounting Flange Bolt Torque | 13 N·m (115 in-lb) M6 flange bolts |
| Fuel Line Nut Torque | 30 N·m (22 lb-ft) high-pressure rail delivery line union nut |
| Drive Interface | Heat-Treated Hardened Tappet Roller Bucket |
| Inlet Low-Pressure Feed | Quick-Connect Hose Barb with Pressure Dampener (5.0 bar) |
| Manufacturer | Bosch (Tier-1 OEM for BMW AG) |
| Bosch Production Number | 0261520141 / 0261520142 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Low-Pressure Supply Disconnection & Residual Depressurization: Depressurize fuel system using ISTA diagnostic software or by pulling the EKP fuel pump control module fuse. Disconnect negative battery terminal in trunk.
- Engine Acoustic Cover & Vacuum Lines Removal: Remove acoustic beauty cover, intake charge pipe brackets, and vacuum reservoir hoses to access the high-pressure pump mounted on the intake side of the cylinder head.
- High-Pressure Steel Rail Line Removal: Use a 17mm flare nut wrench with counter-hold on pump hex fitting to loosen high-pressure steel delivery line. Disconnect low-pressure supply line.
- Pump Removal & Roller Tappet Inspection: Evenly loosen the two M6 mounting bolts. Extract the pump and inspect the internal roller tappet bucket for surface galling or wear on the camshaft drive lobe.
- New Pump Installation & Torque Sequence: Lubricate new Viton O-ring and roller tappet with engine oil. Rotate engine until cam lobe is at lowest point. Torque mounting bolts to 13 N·m (115 in-lb) and high-pressure line nut to 30 N·m (22 lb-ft).
- Confirm the engine code and EPC fitment before installing the pump.
- Torque the pump hold-down fasteners to 13 N·m and the high-pressure line to 30 N·m.
- Record the listed DTCs before clearing them, and confirm any coding, adaptation, or seal-reuse requirement in the vehicle documentation.
Frequently Asked Questions
Will this high-pressure fuel pump fit my BMW?
This pump is listed for BMW N20/N26/N55/S55 engines in the F30 3 Series (2012-2016), F10 5 Series (2012-2016), and F25 X3 (2013-2017). Cross references include 13517588879, 7588879, 0261520141, 0261520142, 13518604229, and 8604229. Confirm fitment against the vehicle's EPC if unsure.
What torque specs and system pressure apply to this pump?
The listed mounting/hold-down torque is 13 N·m, the high-pressure line torque is 30 N·m, and system pressure is 200 bar. Use these verified values for the specified pump.
What diagnostic trouble codes are listed for this high-pressure fuel pump?
The verified diagnostic trouble codes listed for this pump are P0300, P0087, P0193, P0089, and P0191. A code-to-symptom mapping is not stated, so confirm diagnosis rather than guessing.
Does replacement require coding/adaptation or new seals, and how do I verify the old part?
Coding/adaptation requirements and seal reuse are not stated in the verified facts; confirm them against the vehicle's EPC/service documentation. To verify the old part, compare the cross references 13517588879, 7588879, 0261520141, 0261520142, 13518604229, and 8604229.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.