Catalog / BOSCH / 06H906036Q
BOSCH

BOSCH 06H906036Q

View Specs
SolenoidGasoline Direct Injection (GDI / HDEV)Euro 5

High Pressure Fuel Injector VW Golf GTI Passat Audi A4 A5 Q5 1.8 2.0 TSI EA888 Gen 2

Reference data for BOSCH 06H906036Q common rail injector · OEM 06H906036G, 06H906036P, 06H906036E, 06H906036AB, 0261500076, 0261500075 · Application Volkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC)
OE REFERENCE06H906036G, 06H906036P, 06H906036E, 06H906036AB, 0261500076, 0261500075
CONTROL VALVEHIGH-PRESSURE SOLENOID ACTUATED NEEDLE PINTLE VALVE
NOZZLE6-Hole Asymmetric Laser Micro-Aperture Tip
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

The 06H906036Q is an industrial-grade genuine Tier-1 replacement engineered for VW-Audi 1.8 TSI / 2.0 TSI EA888 Gen 2 (CCZA, CCZB, CAEB, CDNC, CCTA). Designed for high-precision VAG FSI/TSI High-Pressure Direct Homogeneous Injection, it delivers factory calibration standards, OE cross-reference compatibility, and verified workshop reliability.

Before You Order

Always verify the OE reference 06H906036G, 06H906036P, 06H906036E, 06H906036AB stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 06H906036Q needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Volkswagen Golf VI GTI 2.0 TSIVolkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC)2009-2013
Audi A4 (B8)Volkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC)2008-2015
Audi Q5 (8R)Volkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC)2009-2016
04

Technical Specifications

SpecificationValue
System TypeBosch HDEV5 Solenoid Multi-Hole Direct Injection Injector
Maximum Operating PressureCore Spec
Nozzle GeometryCore Spec
Coil Resistance1.5 - 2.5 Ohms (Peak and Hold High Current Driver)
Fuel Rail Fastener Torque9 N·m M6 Retaining Bolts
High Pressure Pipe Joint Torque27 N·m Flare Nut Connection
Diagnostic Trouble CodesP0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0172 (System Too Rich Bank 1)
Common Failure ModeNozzle carbon fouling and internal seat leakage causing overnight fuel drip, wet spark plugs & cold start misfire
Operating PressureCore Spec

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

BOSCHExact Engine & Chassis Match
06H127025K
Gasoline Direct Injection (GDI) • 200 bar
🚙 Audi A4 (B8) (CAEB)
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
06H127025N
Gasoline Direct Injection (GDI) • 150 bar
🚙 Audi A4 (B8) (CAEB)
Technical Specifications & Pinout
HITACHIExact Engine & Chassis Match
06H127025Q
Gasoline Direct Injection (GDI) • 150 bar
🚙 Audi A4 (B8) (CAEB)
Technical Specifications & Pinout
05

Installation Tips

  1. Remove Intake Manifold & Relieve Fuel Pressure: Depressurize fuel system. Disconnect battery. Remove upper intake manifold assembly to expose high-pressure fuel rail and direct injectors.
  2. Use T10133 Slide Hammer Tool to Extract Injectors: Install factory extraction puller tool T10133 onto injector grooved collar. Slide hammer straight outward along injector bore axis to prevent damage to head pocket.
  3. Clean Cylinder Head Injector Bores Thoroughly: Use brass bore brush tool to ream carbon debris from injector combustion tip seat pockets in cylinder head. Blow out clean with compressed air.
  4. Install New Teflon Combustion Seal with Calibration Cone: Slide brand-new Teflon seal ring over expanding cone tool. Size into final groove using calibration sleeve T10133/2 until diameter shrinks to factory spec.
  5. Assemble Fuel Rail & Torque Fasteners: Push injectors into fuel rail with support clips. Align tips into cylinder head. Tighten fuel rail mounting bolts to 9 N·m and high pressure steel line to 27 N·m.
Tips & Warnings:
  • Torque the mounting/hold-down to 9 N·m.
  • Torque the high-pressure line to 27 N·m.
  • Confirm part number 06H906036Q and its listed cross references before fitment.
06

Frequently Asked Questions

QWhy do EA888 Gen 2 engines experience cold morning misfires (P0301-P0304)?

Carbon varnish deposits on the microscopic 6-hole nozzle tips and internal needle seat wear in the 06H906036Q injector allow pressurized fuel to drip into the combustion chamber overnight. This soaks the spark plug, producing severe misfire codes upon cold startup.

QCan I reuse the Teflon combustion chamber seal ring?

Never. The Teflon sealing ring is compressed during initial installation to seal against 150+ bar combustion chamber pressures. Reusing an old seal causes blow-by leakage, torching the cylinder head bore and destroying the injector body.

QWhat is the proper tightening torque for the EA888 Gen 2 fuel rail?

The fuel rail mounting bolts into the cylinder head require 9 N·m. The high pressure fuel supply pipe flare nut must be torqued to 27 N·m.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol