Delphi 28236383
common rail injector
03P130277, 03P130277A28239294G3741800 bar peak rail pressureProduct Overview
The Delphi 28236383 is an authentic common rail diesel injector calibrated for Volkswagen Polo V (6R) and CFWA engine applications. Operating at an engineered rail pressure of 1800 bar, this solenoid assembly features the precision 28239294 control valve and G374 nozzle. Mandatory ECU calibration requires programming the cylinder-specific C3i 20-digit code into the engine control unit to establish smooth delivery balance and Euro 5 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Polo V (6R) | 1.2 TDI (CFWA) | 2009-2014 |
| Seat Ibiza IV (6J) | 1.2 TDI (CFWA) | 2010-2015 |
| Skoda Fabia II (542) | 1.2 TDI (CFWA) | 2010-2014 |
| Skoda Roomster (5J) | 1.2 TDI (CFWA) | 2010-2015 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | 28236383 |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 20 N·m + 90° |
| High-Pressure Line Torque | 20 N·m + 90° |
| Coding Required | Yes |
| Emission Standard | Euro 5 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 20 N·m, then rotate a further 90°, then reconnect the high-pressure line and tighten it to 20 N·m, then rotate a further 90°; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm the exact vehicle application against the EPC before ordering 28236383.
- Verify any coding or adaptation requirements for 28236383 against the vehicle's workshop manual.
- Follow the vehicle manufacturer's workshop procedure when diagnosing or installing this common-rail diesel injector.
Frequently Asked Questions
Which vehicles is 28236383 listed for?
28236383 is listed for the CFWA engine family in the Volkswagen Polo, SEAT Ibiza, Skoda Fabia and Skoda Roomster applications shown; confirm exact fitment against the vehicle's EPC or workshop manual.
What symptoms indicate a failed injector?
The supplied product data does not list failure symptoms for 28236383; diagnose common-rail injector faults using the vehicle manufacturer's workshop procedures and confirm findings against the workshop manual.
What should I check before ordering 28236383?
Before ordering 28236383, confirm the engine family and the existing injector identification against the EPC or workshop manual, and verify that the listed vehicle applications match your vehicle.
Must the old injector be coded or adapted?
The supplied information does not state coding or adaptation requirements for 28236383; confirm whether matching or adaptation is needed against the vehicle's EPC or workshop manual before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.