Catalog / DELPHI / 28337917
DELPHI

28337917

View Specs
SolenoidDelphi Common Rail SystemEuro 6

Delphi Bobcat D24 Injector 7030364 Specs & Data

Reference data for DELPHI 28337917 common rail injector · OEM 28337919, 28344074, 28388960, 28384645, 7030364, 7261663, 7030364REM, 400903-00074, 400903-00074D · Application Doosan D18 / D24 (1.8L & 2.4L Tier 4 Common Rail)
OE REFERENCE28337919, 28344074, 28388960, 28384645, 7030364, 7261663, 7030364REM, 400903-00074, 400903-00074D
CONTROL VALVE28239294
NOZZLEG374
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Delphi 28337917 (Bobcat OE part numbers 7030364, 7261663, and Doosan reference 400903-00074) is a heavy-duty, fast-switching electro-hydraulic common rail diesel injector from the Delphi DFI 1.5 family. Engineered specifically for Doosan Infracore D24 NAPAP (2.4L) and D18 (1.8L) non-road diesel engines, it meets strict EPA Tier 4 Final / EU Stage IV emissions standards without requiring a Selective Catalytic Reduction (SCR) urea system on most models. Operating at hydraulic rail pressures up to 1800 bar, this injector powers thousands of Bobcat compact construction machines worldwide, including the S550 / S570 / S590 skid-steer loaders, T590 / T595 compact track loaders, and E35 / E42 / E50 mini excavators. Its ultra-fast hydraulic response is controlled by a micro-lapped Delphi control valve 28239294 and a 7-hole DLC-coated nozzle G374 (28344074). After mechanical torquing of the hold-down clamp bolt to 28 N·m (21 lb·ft), the unique 20-character hexadecimal Delphi C3i compensation code etched on the solenoid cap must be programmed into the engine ECM using Bobcat Service Analyzer or a certified heavy-machinery scan tool.

Before You Order

Always verify the OE reference 28337919, 28344074, 28388960, 28384645 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 28337917 needs its calibration code transferred after fitting; read the code from the new unit and program it with a compatible diagnostic tool.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Bobcat S530 / S570 / S590 / T590Doosan D18 / D24 (1.8L & 2.4L Tier 4 Common Rail)2014-2022
Doosan D24 / D18Doosan D18 / D24 (1.8L & 2.4L Tier 4 Common Rail)2014-2022
04

Technical Specifications

SpecificationValue
INJECTOR TYPECommon Rail Injector
SYSTEM PLATFORMCRI
CONTROL VALVECore Spec
🔗 Shared Valve (40 assemblies):2823638228236383EJBR00801ZEJBR01101Z
NOZZLE CODECore Spec
🔗 Shared Nozzle (7 assemblies):282322482823638328342997EMBR00001D
OPERATING PRESSURECore Spec
05

Installation Tips

  1. Record 20-Digit C3i Code: Prior to installation, transcribe the 20-digit alphanumeric code stamped on the plastic connector collar of each injector.
  2. Purge Injector Bore: Thoroughly scrub the cylinder head injector sleeve using a brass brush and specialized seat reamer kit to eliminate all carbon glaze. Vacuum debris out completely.
  3. Replace Flame Washer: Install a brand-new 1.5 mm stepped copper washer (ID 7.8 mm / OD 15.2 mm). Never reuse old copper washers; combustion gas blow-by will bake the nozzle and seize the delicate Delphi control valve.
  4. Seat Injector: Apply a light film of clean engine oil to the body O-ring and lower the injector vertically into the bore until it seats firmly against the cylinder head base.
  5. Clamp Fork Torque: Position the hold-down clamp fork and torque the clamp bolt to 28 N·m (21 lb·ft). Avoid uneven side-loading.
  6. High-Pressure Pipe: Connect the high-pressure fuel line and torque the flare nut to 30 N·m (22 lb·ft).
  7. Fuel Return Line: Install the spill rail with new seals and tighten the return banjo to 15 N·m (11 lb·ft).
  8. Program C3i Code: Connect Bobcat Service Analyzer or an industrial diagnostic tablet. Navigate to ECM Configuration -> Injector Calibration and write the 20-character C3i code for the replaced cylinder.
  9. Fuel System Bleeding: Cycle the electric priming pump 3-4 times before cranking to vent air pockets. Run the machine until coolant reaches 70°C and verify smooth idle balance.
Tips & Warnings:
  • Verify part number 28337917 and the listed cross references against the vehicle's EPC before installation.
  • Tighten the mounting / hold-down to 28 N·m and the high-pressure line to 30 N·m.
  • Confirm coding/adaptation, seal-reuse and service-life guidance against the vehicle's EPC/service information before installation.
06

Frequently Asked Questions

QWhat vehicles and engine family does part 28337917 fit, and which cross-reference numbers should I check?

Fitment is listed for Bobcat S530 / S570 / S590 / T590 (2014-2022) and Doosan D24 / D18 (2014-2022), with engine family Doosan D18 / D24 (1.8L & 2.4L Tier 4 Common Rail). Cross references to check are 28337917, 28337919, 28344074, 28388960, 28384645 and 7030364. Confirm any fitment or number not listed against the vehicle's EPC instead of guessing.

QWhat diagnostic trouble codes are listed for this injector, and what symptoms indicate a failed unit?

The listed diagnostic trouble codes are P0300, P0301, P0087, P0302 and P0304. The verified facts do not state additional failure symptoms, so confirm diagnosis against the vehicle's EPC/service information rather than guessing.

QWhat are the torque settings and system pressure for this common-rail diesel injector?

Mounting / hold-down torque is 28 N·m, and high-pressure line torque is 30 N·m. System pressure is 1800 bar. These are the only torque and pressure values provided for part 28337917.

QDoes this injector require coding/adaptation, can the seals be reused, and what service life should I expect?

The verified facts do not state coding/adaptation requirements, seal-reuse guidance or expected service life for part 28337917. Confirm these points against the vehicle's EPC/service information before installation, and do not guess.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol