Delphi 28388960
common rail injector
1980L3, 968619108028278897G3791800 bar peak rail pressureProduct Overview
The Delphi 28388960 is an authentic common rail diesel injector calibrated for Peugeot 508 I and DW10CTED4 engine applications. Operating at an engineered rail pressure of 1800 bar, this solenoid assembly features the precision 28278897 control valve and G379 nozzle. Mandatory ECU calibration requires programming the cylinder-specific C3i 20-digit code into the engine control unit to establish smooth delivery balance and Euro 5 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | 28388960 |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 30 N·m + 65° |
| High-Pressure Line Torque | 30 N·m + 65° |
| Coding Required | Yes |
| Emission Standard | Euro 5 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 30 N·m, then rotate a further 65°, then reconnect the high-pressure line and tighten it to 30 N·m, then rotate a further 65°; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Before fitting part 28388960, confirm the engine-family match and any coding or adaptation steps in the workshop manual.
- Inspect the fuel system and leak-off results before condemning the injector, and follow the manufacturer's cleanliness procedure.
- Use the vehicle's EPC and workshop data to verify fitment and tightening specifications before work begins.
Frequently Asked Questions
Will this injector fit my vehicle?
It is listed for the Peugeot and Citroen applications in the RHH, RHE or RHD engine family. Confirm your vehicle details against the EPC before ordering part 28388960.
What symptoms suggest a failed injector?
Common signs include rough running, misfire, poor starting, excessive smoke, fuel smell or a persistent injector-related fault code. Confirm diagnosis with live data and leak-off testing before replacing part 28388960.
What should I check before ordering?
Check the engine family marked for the vehicle, compare the old injector visually, and confirm coding or adaptation requirements in the workshop manual. If any detail is unclear, verify it against the EPC before ordering 28388960.
Must the replacement injector be coded or adapted?
Coding or matching requirements are not stated here, so confirm them against the vehicle's EPC or workshop manual. Do not assume the replacement can be fitted without the specified diagnostic procedure for 28388960.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.