Delphi EMBR00101D
common rail injector
1681997, 9M5Q-9K546-BA, 1980EQ28278897G3791800 bar peak rail pressureProduct Overview
The Delphi EMBR00101D is an authentic common rail diesel injector calibrated for Ford Mondeo IV and DW10C engine applications. Operating at an engineered rail pressure of 1800 bar, this solenoid assembly features the precision 28278897 control valve and G379 nozzle. Mandatory ECU calibration requires programming the cylinder-specific C3i 20-digit code into the engine control unit to establish smooth delivery balance and Euro 5 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EMBR00101D |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 30 N·m + 65° |
| High-Pressure Line Torque | 30 N·m + 65° |
| Coding Required | Yes |
| Emission Standard | Euro 5 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 30 N·m, then rotate a further 65°, then reconnect the high-pressure line and tighten it to 30 N·m, then rotate a further 65°; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Tighten the injector mounting/hold-down to 30 N·m + 65°.
- Tighten the high-pressure line to 30 N·m + 65°.
- Verify part number EMBR00101D and cross references 28388960, 1681997, 9M5Q-9K546-BA and 1980EQ against the vehicle EPC before fitting.
Frequently Asked Questions
Is this injector compatible with DW10C, TXDA and UFBA engines?
The verified engine family list is DW10C, TXDA and UFBA. The verified fitment includes Ford Mondeo IV 2.0 TDCi Duratorq (TXDA) 2010-2014, Ford S-Max I 2.0 TDCi Duratorq (UFBA) 2010-2014, and Peugeot Expert II 2.0 HDi (RH02) 2011-2016. Confirm against the vehicle EPC before ordering.
How do I verify the old injector matches this listing?
Compare the old unit with part number EMBR00101D and the listed cross references 28388960, 1681997, 9M5Q-9K546-BA and 1980EQ. If the markings do not match, confirm fitment against the vehicle EPC before ordering.
What fault codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0204 and P0202. The verified facts do not include symptom descriptions, so confirm the diagnosis with vehicle diagnostics and the vehicle EPC or OEM procedure.
Are coding/adaptation and seal reuse specified for this injector?
The verified facts do not state coding/adaptation or seal-reuse requirements. Confirm both against the vehicle EPC or OEM workshop procedure before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.