Catalog / DELPHI / EMBR00002D
DELPHI

Delphi EMBR00002D

View Specs
SolenoidDelphi Common Rail SystemEuro 6

common rail injector

Reference data for DELPHI EMBR00002D common rail injector · OEM A6510702787, A6510700487, 6510702787 · Application OM651, OM651.950, OM651.956
OE REFERENCEA6510702787, A6510700487, 6510702787
CONTROL VALVE28278897
NOZZLEG379
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Delphi EMBR00002D is an authentic common rail diesel injector calibrated for Mercedes-Benz C-Class (W205) and OM651 engine applications. Operating at an engineered rail pressure of 2000 bar, this solenoid assembly features the precision 28278897 control valve and G379 nozzle. Mandatory ECU calibration requires programming the cylinder-specific C3i 20-digit code into the engine control unit to establish smooth delivery balance and Euro 6 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.

Before You Order

Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Mercedes-Benz C-Class (W205)C 220 BlueTEC (OM651.921)2014-2018
Mercedes-Benz GLC (X253)220 d 4MATIC (OM651.921)2015-2019
Mercedes-Benz V-Class (W447)V 220 BlueTEC (OM651.950)2014-2020
04

Technical Specifications

SpecificationValue
SKUEMBR00002D
BrandDELPHI
Fuel SystemCommon Rail (Delphi DFI)
Operating PressureCore Spec
Control ValveCore Spec
🔗 Shared Valve (10 assemblies):28388960EMBR00001DEMBR00101DEMBR00301D
Nozzle CodeCore Spec
🔗 Shared Nozzle (11 assemblies):2834837128388960EMBR00101DEMBR00201D
Hold Down Torque15 N·m + 90°
High-Pressure Line Torque15 N·m + 90°
Coding RequiredYes
Emission StandardEuro 6
05

Installation Tips

  1. Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
  2. Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
  4. Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
  5. Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
  6. Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 15 N·m, then rotate a further 90°, then reconnect the high-pressure line and tighten it to 15 N·m, then rotate a further 90°; reconnect the electrical connector and spill connection.
  7. Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
  8. Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
Tips & Warnings:
  • Confirm the exact vehicle application and part number EMBR00002D against EPC or workshop data before ordering.
  • Check diagnostic data before condemning the injector, since coding and adaptation requirements are not stated for this unit.
  • Follow the workshop manual for removal, installation and tightening, and confirm seal reuse or replacement there.
06

Frequently Asked Questions

QWill EMBR00002D fit my Mercedes-Benz?

EMBR00002D is listed for the Mercedes-Benz C-Class, GLC and V-Class diesel applications shown in the fitment data; confirm the exact vehicle by EPC or workshop manual before ordering.

QWhat symptoms indicate the injector may need replacement?

The listing does not state failure symptoms; if a common-rail diesel injector fault is suspected, confirm diagnosis with the vehicle workshop data before replacing EMBR00002D.

QWhat should I check before ordering this injector?

Check that the vehicle matches the listed Mercedes-Benz applications and verify EMBR00002D against the vehicle's EPC or workshop manual; also confirm any required coding or adaptation before ordering.

QDoes the replacement injector need coding or matching?

Coding or matching requirements are not stated for EMBR00002D; confirm whether adaptation is needed against the vehicle's EPC or workshop manual before installation.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol