Delphi EMBR00201D
common rail injector
03P130277B28239294G3791800 bar peak rail pressureProduct Overview
The Delphi EMBR00201D is an authentic common rail diesel injector calibrated for Volkswagen Polo V BlueMotion and CFWA engine applications. Operating at an engineered rail pressure of 1800 bar, this solenoid assembly features the precision 28239294 control valve and G379 nozzle. Mandatory ECU calibration requires programming the cylinder-specific C3i 20-digit code into the engine control unit to establish smooth delivery balance and Euro 5 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Polo V BlueMotion | 1.2 TDI (CFWA) | 2010-2014 |
| Seat Ibiza Ecomotive | 1.2 TDI (CFWA) | 2011-2015 |
| Skoda Fabia Greenline | 1.2 TDI (CFWA) | 2010-2014 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EMBR00201D |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 20 N·m + 90° |
| High-Pressure Line Torque | 20 N·m + 90° |
| Coding Required | Yes |
| Emission Standard | Euro 5 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 20 N·m, then rotate a further 90°, then reconnect the high-pressure line and tighten it to 20 N·m, then rotate a further 90°; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm the engine family CFWA and the listed vehicle fitment against the EPC before ordering.
- Apply 20 N·m + 90° to the mounting/hold-down and high-pressure line as specified.
- Verify the old injector by checking part number EMBR00201D and cross references 28236383 and 03P130277B.
Frequently Asked Questions
Will this common-rail diesel injector fit my Volkswagen Polo V BlueMotion 1.2 TDI?
It is listed for Volkswagen Polo V BlueMotion 1.2 TDI (CFWA) 2010-2014, SEAT Ibiza Ecomotive 1.2 TDI (CFWA) 2011-2015, and Skoda Fabia Greenline 1.2 TDI (CFWA) 2010-2014. Confirm the exact vehicle and engine code against the vehicle's EPC before ordering.
Which diagnostic trouble codes are listed for this injector, and what symptoms should I check?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0202, and P0203. Specific symptom mapping is not stated in the verified information, so confirm any symptom-to-fault mapping against the vehicle's EPC instead of guessing.
Does this injector require coding or adaptation, and can the seals be reused?
Coding/adaptation requirements and seal reuse are not stated in the verified information. Confirm both against the vehicle's EPC instead of guessing.
What are the mounting/hold-down and high-pressure line torque values, and how can I verify the old part?
The mounting/hold-down torque is 20 N·m + 90°, and the high-pressure line torque is 20 N·m + 90°. To verify the old part, check for part number EMBR00201D and cross references 28236383 and 03P130277B. If the markings are unclear, confirm against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.