Catalog / DELPHI / EMBR00301D
DELPHI

DELPHI EMBR00301D

View Specs
SolenoidDelphi Common Rail SystemEuro 6

Common Rail Injector for Mercedes Benz C Class (W205) OM651

Reference data for DELPHI EMBR00301D common rail injector · OEM A6510702887, A6510703087, A6510703287 · Application OM651
OE REFERENCEA6510702887, A6510703087, A6510703287
CONTROL VALVE28278897
NOZZLEG379
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Delphi EMBR00301D is an authentic common rail diesel injector calibrated for Mercedes-Benz C-Class (W205) and OM651 engine applications. Operating at an engineered rail pressure of 2000 bar, this solenoid assembly features the precision 28278897 control valve and G379 nozzle. Mandatory ECU calibration requires programming the cylinder-specific C3i 20-digit code into the engine control unit to establish smooth delivery balance and Euro 6 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.

Before You Order

Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Mercedes-Benz C-Class (W205)C 200 d / C 220 d (OM 651.921)2014-2018
Mercedes-Benz E-Class (W213)E 200 d / E 220 d (OM 651.921)2016-2019
Mercedes-Benz GLC (X253)220 d (OM 651.921)2015-2019
Mercedes-Benz Sprinter (W907)214 CDI / 314 CDI / 316 CDI2018-2022
04

Technical Specifications

SpecificationValue
SKUEMBR00301D
BrandDELPHI
Fuel SystemCommon Rail (Delphi DFI)
Operating PressureCore Spec
Control ValveCore Spec
🔗 Shared Valve (10 assemblies):2823638128342997EMBR00002DEMBR00101D
Nozzle CodeCore Spec
🔗 Shared Nozzle (11 assemblies):2823224228236381EMBR00101DEMBR00201D
Hold Down Torque15 N·m + 90°
High-Pressure Line Torque27 N·m
Coding RequiredYes
Emission StandardEuro 6
05

Installation Tips

  1. Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
  2. Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
  4. Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
  5. Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
  6. Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 15 N·m, then rotate a further 90°, then reconnect the high-pressure line and tighten it to 27 N·m; reconnect the electrical connector and spill connection.
  7. Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
  8. Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
Tips & Warnings:
  • Use clean fuel-system practices and replace disturbed seals only after confirming the required procedure in the workshop manual.
  • Before removal, capture diagnostic data and compare injector correction values so the replacement can be assessed afterward.
  • Confirm coding, adaptation and torque requirements against the vehicle's workshop data before fitting EMBR00301D.
06

Frequently Asked Questions

QWhich vehicles does EMBR00301D fit?

It is listed for Mercedes-Benz C-Class, E-Class, GLC and Sprinter diesel applications with the specified engine family; confirm your VIN/engine code against EPC or workshop data before ordering.

QWhat symptoms suggest a failed injector?

Common signs can include rough idle, misfire, poor starting, smoke, power loss or fuel smell, but these are not exclusive; diagnose fault codes and injector corrections before replacing EMBR00301D.

QWhat should I check before ordering EMBR00301D?

Verify the vehicle's engine code and injector position against EPC/workshop data, inspect the harness and fuel system, and confirm coding or adaptation requirements for your application.

QMust the old unit be matched or adapted?

Coding or adaptation requirements vary by vehicle and control system; confirm the exact procedure in the vehicle's workshop manual, and do not assume plug-and-play fitment for EMBR00301D.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088High

Fuel Rail/System Pressure Too High

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol