DENSO 16600-1VA0A
Direct Fuel Injector Nissan Altima Rogue Qashqai Sylphy Serena 2.0L MR20DD 297500 1170
16600-1VA0B, 297500-1170, FJ1230--150 bar peak rail pressureProduct Overview
The 16600-1VA0A is an original equipment (DENSO) precision component engineered specifically for the Nissan 2.0L Direct Injection DOHC 16V MR20DD. Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0302, P0171.
Always verify the OE reference 166001VA0B, 2975001170, FJ1230 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16600-1VA0A needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16600-1VA0A |
| Manufacturer Brand | DENSO |
| Component Type | Direct Fuel Injector |
| Engine Application | Nissan 2.0L Direct Injection DOHC 16V MR20DD |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 22 N-m (16 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0302, P0171 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 22 N-m (16 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Before fitting, inspect the injector bore, sealing surfaces and connector for contamination or damage.
- Use the vehicle's workshop manual to confirm the correct installation procedure and torque specification.
- After installation, verify fuel-tightness and check for leaks before returning the vehicle to service.
Frequently Asked Questions
Will this injector fit my Nissan X-Trail, Qashqai or Rogue Sport?
It is listed for those Nissan petrol direct-injection applications, but fitment varies by engine and market. Confirm your exact vehicle against the EPC using the VIN before ordering 16600-1VA0A.
What symptoms suggest the injector has failed?
Look for misfire, rough idle, poor cold running, fuel smell, lean or rich running symptoms, and a check-engine light. Confirm diagnosis with a scan tool and the workshop manual before replacing 16600-1VA0A.
What should I check before ordering this injector?
Verify the VIN, engine variant and EPC listing, inspect the connector and wiring, and confirm the fault is injector-related. Also check that the old unit's seals and fitting hardware are addressed per the workshop manual for 16600-1VA0A.
Does the new injector need to be coded or matched to the vehicle?
Coding, matching or adaptation requirements are not stated here. Check the vehicle's EPC and workshop manual for the required procedure, and confirm any calibration steps before fitting 16600-1VA0A.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.