BOSCH 04E906036AR
Fuel Injector VW Golf 7 Passat Tiguan Audi A3 1.4T 1.5T EA211 TSI 0261500245
04E906036AF, FJ1342, 0261500245--200 bar peak rail pressureProduct Overview
The 04E906036AR is an original equipment (BOSCH) precision component engineered specifically for the Volkswagen-Audi Group 1.4L TSI (EA211) & 1.5L TSI DOHC 16V Turbocharged I4. Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0172.
Always verify the OE reference 04E906036AF, FJ1342 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 04E906036AR needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf Mk7 / Jetta / Passat / Tiguan | CZDA / CZEA / CHPA / DADA | 2013-2020 |
| Audi A3 (8V) / Q3 (8U) | CZDA / CZEA / CHPA / DADA | 2013-2019 |
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 04E906036AR |
| Manufacturer Brand | BOSCH |
| Component Type | Direct Fuel Injector |
| Engine Application | Volkswagen-Audi Group 1.4L TSI (EA211) & 1.5L TSI DOHC 16V Turbocharged I4 |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 22 N-m (16 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0172 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 22 N-m (16 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify part number 04E906036AR and the engine code against the vehicle’s EPC before ordering.
- Tighten the injector mounting/hold-down to 10 N·m.
- Tighten the high-pressure line to 22 N·m.
Frequently Asked Questions
Will this injector fit my vehicle?
This injector, part number 04E906036AR, is listed for Volkswagen Golf Mk7 / Jetta / Passat / Tiguan with engine codes CZDA, CZEA, CHPA, or DADA (2013–2020). It is also listed for Audi A3 (8V) / Q3 (8U) with those engine codes (2013–2019). Confirm fitment by VIN and engine code against the vehicle’s EPC before ordering.
Which diagnostic trouble codes are listed for this injector?
The verified diagnostic trouble codes for this injector listing are P0300, P0301, P0302, P0304, and P0087. Use these codes as diagnostic leads only.
Does this injector require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the verified facts for this injector. Confirm whether coding/adaptation is required against the vehicle’s EPC before installation.
Can I reuse the seals, and how do I verify the old part?
Seal reuse is not stated in the verified facts; confirm it against the vehicle’s EPC. To verify the old injector, check its number against 04E906036AR, 04E906036AF, 04E906036Q, 04E906036E, FJ1342, and 0261500245. Confirm final fitment with the vehicle’s EPC using the engine code.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.