DENSO PY8W-13-350
High Pressure Fuel Pump Mazda CX 9 CX 5 Mazda 6 2.5T SkyActiv G PY8W13350A
PY8W-13-350A, GDP501--200 bar peak rail pressureProduct Overview
The PY8W-13-350 is an original equipment (DENSO) precision component engineered specifically for the Mazda 2.5L Turbo SkyActiv-G DOHC 16V (PY-VPTS / PY-VPS). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P0191.
Always verify the OE reference PY8W13350A, GDP501 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. PY8W-13-350 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | PY8W-13-350 |
| Manufacturer Brand | DENSO |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Mazda 2.5L Turbo SkyActiv-G DOHC 16V (PY-VPTS / PY-VPS) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 20 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P0191 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (15 lb-ft), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify the part number and cross references before installing the pump.
- Tighten the pump mounting/hold-down to 20 N·m and the high-pressure line to 30 N·m.
- Confirm fitment by VIN/EPC for Mazda 3, CX-5, or Mazda 6 2.5 applications before ordering.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Mazda?
PY8W-13-350 is listed for Mazda 3 (PE-VPS/PY-VPS/PY-VPTS, 2014-2023), Mazda CX-5 (PE-VPS/PY-VPS/PY-VPTS, 2013-2023), and Mazda 6 2.5 (PE-VPS/PY-VPS/PY-VPTS, 2014-2021). It is for the Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo engine family (PE-VPS / PY-VPS / PY-VPTS). Confirm VIN/EPC fitment before ordering.
What DTCs or symptoms indicate a problem with this pump?
The verified DTCs listed for this high-pressure fuel pump are P0300, P0087, P0193, P0089, and P0191. Symptom descriptions and expected service life are not stated in the verified facts, so confirm diagnosis against the vehicle's EPC/repair information before replacing the pump.
Does this high-pressure fuel pump require coding or adaptation after installation?
Coding/adaptation requirements are not stated in the verified facts. Confirm any required procedure against the vehicle's EPC/repair information before installation.
How do I verify the old pump or a replacement?
Check for part number PY8W-13-350 and the listed cross references: PY8W13350, PY8W13350A, GDP501, PE0113250, and PE0113350B. If the markings do not match, confirm fitment against the vehicle's EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.